Calibration Engineer
Senior Calibration Engineer

GLORY TECHNOLOGY
Calibration & Inspection Company
ABOUT US

.png)
GLORY TECHNOLOGY
Calibration & Inspection Company
Glory Technology Calibration & Inspection Company (GTEC) is providing Calibration & Inspection Services through out the Kingdom of Saudi Arabia. The Company is 100% Saudi owned company and is promoted by a Saudi Engineer with great vision to play a major role in the continuous development of the country by providing quality calibration services to various industries.
​
GTEC is an ISO 17025 accredited calibration laboratory and our capabilities & compliance to International standard ISO 17025 are assessed by International Accreditation Service, IAS USA. GTEC provides quality calibration services for the following parameters:
The Calibration laboratory is equipped with latest master equipment of reputed manufacturers and all our master equipment are traceable to UKAS/DKD/A2LA/IAS/NABL standards. Our highly experienced Technical Staff are committed to delivering quality calibration services and providing you the highest level of customer service. Technically competent and Experienced Calibration Engineers are assigned for each parameter and are adequately resourced to perform the calibration activities.
​
GTEC also provides Lifting Equipment Inspection Service. The Inspection Services are categorised as below:
Lifting Gear Inspection , Load Testing & Certification,Lifting Equipment Inspection & Certification
GTEC is highly equipped with Lifting engineers, Technical experts and all the Modern Equipment and Technologies which effectively takes part in wide range of Lifting Equipment inspection & certification. The objective of this service is to independently assure the safe and proper working capability and condition of each individual crane or lifting and hoisting equipment.
APPROVALS & CERTIFICATES
GTEC is skilled to provide visual inspection and functional test of Elevating/Lifting inspection in accordance with ASME, ANSI/SAIA,BS EN and ISO standard’s.
Elevating lifting equipment such as:
-
Mobile Cranes.
-
Crawler Cranes.
-
Rough Terrain Cranes.
-
Lorry Loader Cranes.
-
EOT cranes.
-
Jib Cranes.
-
Pedestal cranes.
-
Deck cranes.
-
Floor cranes.
-
Provision cranes.
-
Grabs
-
Winches
-
BOP hoists
-
Davits and LARS
​​
-
Gangways, Accommodation Ladders and MOT Ladders.
-
Travel Lift.
-
MEWP / Manlift / Boom lift / Scissor lift / Spider lift
-
Forklifts
-
Telehandler / Telescopic Forklift.
-
Pallet Trucks
-
Wheel Loader.
-
Reach Stacker / Container Handler.
-
Offshore / ISO Containers.
-
Skips, Skids, Baskets, cylinder Racks Etc..
-
Man Baskets / Personnel Baskets / Work Baskets.
-
Spreader Beams / Lifting Beams .
-
Runway beams / Monorails.
-
Powered Hoists.
_edited.jpg)
_edited.jpg)
_edited.jpg)

GTEC is skilled to provide visual inspection, Load Testing & Certification of Lifting Gears such as
-
Wire rope slings / Wire rope.
-
Shackles.
-
Chain slings / Chains.
-
Hooks
-
Clamps
-
Lifters
-
Chain blocks
-
Lever hoists
-
Jaw winches
-
Snatch blocks / Pulleys / Sheaves
-
Eye bolts
-
Webbing slings / Round slings
-
Safety harness / Fall arresters
-
Towing gears
-
Mooring gears
-
Lifting Pad Eyes and Anchor Bolts.
CAREER WITH US
A career at Glory Technology is a flexible partnership between each employee and the company.
We provide the opportunity, the environment and the culture-and you select the path that best fits your career goals.
Send your resume to management@gtecgulf.com
Current Openings
Calibration Engineer
Job Function:
The Calibration Engineer has responsibilities for all testing and calibration activities required by the laboratory, using established procedures and GTEC standard equipment appropriately. Has a command and obligation to calibration technician performing calibration work in and out of laboratory.
Duties and Responsibilities:
• Testing and/or calibrating instruments as per established
procedures
• Preparing and finalizing test / calibration report, repair service report and non-calibration report
• Informing Laboratory Supervisor / Manager about the non-conforming work
• Recommending GTEC laboratory management on any improvement pertaining to test and calibration
Assisting GTEC laboratory management in developing calibration methods aside from standard methods
• Reviewing calibration technician’s report
• Supervising the team especially at on-site calibration
• Implementing good housekeeping in the laboratory
• Observing safety in every aspect of work in the laboratory
​
Minimum Requirements:
• Candidate must possess at least Bachelor’s / Diploma in Engineering
• With min 3 years working experience in an ISO 17025 accredited Calibration Laboratory
• Should be familiar with Dimension Instruments Calibration, Pressure Instruments Calibration, Thermal Instruments Calibration.
• With good commands of oral / written English
• Computer literate
• Can easily understand instructions and work under minimum supervision
• With good communication skills
Senior Calibration Engineer
Job Function:
The Senior Calibration Engineer has responsibilities for all testing and calibration activities required by the laboratory, using established procedures and GTEC standard equipments appropriately. Has a command and obligation to calibration Engineers performing calibration work in and out of laboratory. He should act as deputy to the Technical Manager.
Duties and Responsibilities:
• Testing and/or calibrating instruments as per established procedures
• Preparing and finalizing test / calibration report, repair service report and non-calibration report
• Informing Laboratory Supervisor / Manager about the non-conforming work
• Recommending GTEC laboratory management on any improvement pertaining to test and calibration
• Assisting GTEC laboratory management in developing calibration methods aside from standard methods
• Reviewing calibration technician’s report
• Supervising the team especially at on-site calibration
• Implementing good housekeeping in the laboratory
• Observing safety in every aspect of work in the laboratory
​
Minimum Requirements:
• Candidate must possess at least Bachelor’s / Diploma in Engineering
• With min 3 years working experience in an ISO 17025 accredited Calibration Laboratory
• Should be familiar with Dimension Instruments Calibration, Pressure Instruments Calibration, Thermal Instruments Calibration.
• With good commands of oral / written English
• Computer literate
• Can easily understand instructions and work under minimum supervision
• With good communication skills
GET A QUOTE
REACH US



Our Address
Jubail
Jubail
Haradh
Haradh



E -mail
Glory Technology Calibration and Inspection Co.
Shop # 16 ,1st Industrial Support Area
Al Jubail- 35717,Kingdom of Saudi Arabia
jubail@gtecgulf.com
management@gtecgulf.com
Inside Al drees Petrol Station,Haradh 36911
Kingdom of Saudi Arabia
haradh@gtecgulf.com
management@gtecgulf.com


